High quality Cisco CCNP Wireless 300-360 dumps exam questions and answers free update at Lead4pass. Latest Cisco CCNP Wireless 300-360 dumps pdf and vce training resources. https://www.leads4pass.com/300-360.html dumps pdf questions and answers. Get the best Cisco CCNP Wireless 300-360 dumps pdf training materials and study guides from Lead4pass to have a free try, pass Cisco 300-360 exam test easily.
Download free latest Cisco 300-360 dumps pdf from google drive: https://drive.google.com/open?id=0B_7qiYkH83VRbXA1TGRTOW5TYkE
Download free latest Cisco 300-320 dumps pdf from google drive: https://drive.google.com/open?id=0B_7qiYkH83VRU3Y3elpyNldxUU0
QUESTION 1
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)
A. Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller is installed.
B. Consult with the customer to ensure that the IT staff has a complete set of design and installation documents.
C. Make sure the customer is aware that they should consider purchasing a support contract immediately after the installation is complete.
D. Spend time with the customer to show them the controller GUI and inform them how they can reach the Cisco TAC if they have any problems.
E. Test all the customer’s wireless devices and applications to ensure they are working properly.
Correct Answer: BE
QUESTION 2
A customer is deploying a Greenfield 802.11ac network on a foor that will support approximately 300 wireless devices.
Which setting needs to be changed on Prime Infrastructure Planning Tool in order to predict the amount of access points the customer needs to service the new foor? 300-360 pdf
A. Data Coverage Support Margin
B. Demand Settings
C. Add AP Field
D. 802.11n Protocol Support
Correct Answer: B
QUESTION 3 300-360 dumps
An engineer is preparing for an outdoor wireless survey to mesh connect a distant remote building to a connected building.
Which two types of antennas are appropriate for this application? (Choose two.)
A. circular polarized
B. patch
C. dishD. Yagi
E. omni
Correct Answer: CD
QUESTION 4
An engineer would like to calibrate the RF environment to improve accuracy.
Which wireless attribute is added to the foor-level calculation by calibrating the foor?
A. attenuation
B. TX power
C. multipath
D. SNR
Correct Answer: A
QUESTION 5
What are two advantages of conducting an active survey versus a passive survey when verifying RF coverage? (Choose two.)
A. verifies packet loss
B. verifies roaming
C. verifies SNR
D. verifies signal level
E. verifies interferers
Correct Answer: AB
QUESTION 6
An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs? 300-360 dumps
A. ACU
B. ADU
C. NEMA
D. WLSE
Correct Answer: C
QUESTION 7
An engineer is tuning RRM parameters to improve client connectivity. Which channel band results in the best 802.11n client compatibility?
A. UNII-2
B. UNII-2e
C. UNII-3
D. UNII
E. UNII-1
Correct Answer: E
QUESTION 8
A customer has deployed an N+N redundant wireless infrastructure. In this deployment the access points have been salt and peppered between controllers. 300-360 pdf
What configuration would be necessary to cut down on the use of mobility tunnels for voice clients?
A. mobility anchor
B. KIS based CAC
C. media session snooping
D. re-anchor roamed voice clients
Correct Answer: D
QUESTION 9
Which two steps are associated with the active portion of the audit when a post-installation audit is performed with an auditing tool such as Ekahau? (Choose two.)
A. Check for co-channel interference by standing near an access point on one channel and watching for other access points that are on the same channel.
B. Verify smooth roaming.
C. Check to see if the signal level on other access points that are heard on the same channel is at least 19dBm weaker than the access point that you are next to.
D. Check that all channels are supported by the APs regardless of client capabilities.
E. Verify that the network traffic of physical data rate and packet loss meets user requirements.
Correct Answer: BE
QUESTION 10
An engineer is performing a predictive wireless design for a Parts Distribution Center which requires data and location services. 300-360 dumps Which three requirements are inputs to the design? (Choose three.)
A. access points with directional antennas
B. continuous -67 dBm coverage from one access point
C. overlapping -75 dBm coverage from three access points
D. overlapping -67 dBm coverage from two access points
E. access points in IPS mode
F. continuous -72 dBm coverage from one access point
G. access points in corner sand a long perimeters
Correct Answer: BCG
Read more: https://www.leads4pass.com/300-360.html dumps pdf training materials free download.
Watch the video to learn more:
https://youtu.be/FkFIw8z7vfA
